Why does a gasoline car use only about 12 to 30 percent of its fuel energy to move? The answer is efficiency, a simple ratio you can work out with one division. Students, engineers, and homeowners all use it to compare machines and to see where energy goes.
Efficiency is useful output divided by total input, using the same units. Multiply by 100 for a percent. A motor that takes in 1,200 W and delivers 900 W is 75 percent efficient. A single machine cannot exceed 100 percent, and the Carnot limit caps heat engines even lower.
The Efficiency Formula and Its Three Forms
Efficiency is the ratio of useful output to input, measured in energy terms. Its symbol is the Greek letter eta. The value runs from 0 to 1, or from 0 to 100 percent once you multiply by 100.
The energy can be chemical, electric, mechanical, light, or heat. What matters is that output and input share the same units. Never divide watts by joules.
Efficiency = useful output / total input. Rearrange it and you can solve for any of the three values.
| What you want | Formula | What you must know |
|---|---|---|
| Efficiency | output / input | Output and input |
| Useful output | efficiency x input | Efficiency and input |
| Total input | output / efficiency | Output and efficiency |
Wasted energy is simply input minus output. Efficiency is a ratio, so it has no unit of its own, and 0.75 and 75 percent say exactly the same thing. Use the decimal form, such as 0.75, inside the formulas.
Finding Efficiency: A 1,200 W Motor
Suppose a motor draws 1,200 W and delivers 900 W of mechanical power. Here is how to find its efficiency in four steps.
- Match the units. Both numbers are in watts: 1,200 W in and 900 W out.
- Divide output by input. 900 / 1,200 = 0.75.
- Convert to a percent. 0.75 x 100 = 75 percent.
- Find the waste. 1,200 W minus 900 W leaves 300 W wasted.
The wasted 300 W is energy that left the motor in a form you did not want, yet you still pay for it. A higher percentage means less waste for the same useful work. New to watts? Our guide on how to calculate power in watts covers the basics.
Finding Input or Output When Efficiency Is Known
Often you know the efficiency and need one of the other numbers. Rearrange the formula and the answer is one step away.
- Find the input. You need 600 W of useful output from a machine that is 80 percent efficient. Input = 600 / 0.80 = 750 W, so 150 W is wasted.
- Find the output. A 40 percent efficient engine is fed 2,500 J. Output = 0.40 x 2,500 = 1,000 J, so 1,500 J is wasted.
Both examples use the same formula, just turned around. The first shows that a less efficient machine must draw more input to do the same job. The second shows how little useful energy a 40 percent engine returns from its fuel.
Use 0.80, not 80, in these formulas. To check your own numbers, enter any two values into the efficiency calculator. It solves the third and shows the energy wasted.
Why Gasoline Cars Waste More Energy Than EVs
The US Department of Energy and EPA report that only about 12 to 30 percent of a conventional vehicle’s fuel energy moves it down the road. The range depends on the drive cycle. The rest is lost in the engine and driveline or used to power accessories.
For electric cars, the same agencies list 60 to 66 percent in city driving and 71 to 73 percent on the highway. These figures measure the share of energy that reaches the wheels, not a fixed rating. Charging adds losses of its own, such as AC to DC conversion and battery resistance, and they vary. This gap is why EVs score so much higher on this one measure.
Counting regenerative braking can push the EV figure above 94 percent in the city. For range, see how to calculate real EV range. For engine ratings, read horsepower vs watts.
How Efficiencies Multiply Across Several Stages
Many systems pass energy through several steps. Each stage keeps only part of what it receives, so you multiply the stage efficiencies together.
Take three example stages with made-up values of 0.90, 0.80, and 0.95. First, 0.90 x 0.80 = 0.72. Then 0.72 x 0.95 = 0.684, so the whole chain is 68.4 percent efficient.
That result is lower than the weakest single stage, which is 0.80. Adding the percentages instead would give a wrong and far too high answer.
Real chains work the same way. A device might lose some energy making power, some in a cable, and some in the final machine. Each loss shrinks what is left for the next step.
The Carnot Limit and Why Heat Pumps Beat 100 Percent
A heat engine turns heat into work, and its best possible efficiency is (hot temperature – cold temperature) / hot temperature. Both temperatures must be in kelvin, where K = degrees C + 273.15. This is the Carnot limit, an idealization that no real engine reaches.
For example, take a hot side of 500 K (about 227 degrees C) and a cold side of 300 K. Then (500 – 300) / 500 = 0.40, so the maximum is 40 percent. Because no real engine is reversible, a real engine will be lower. Raise the hot side or lower the cold side and the limit rises, since the formula grows with the temperature gap.
Heat pumps seem to break the rule because they report COP, a different measure. COP is useful heating or cooling divided by the work needed. A heat pump moves existing heat instead of making it, so its COP usually exceeds 1. See heat pump vs furnace running cost for what that means on a bill.
Common Efficiency Mistakes and How to Fix Them
Most wrong answers come from a few repeat slips. This table lists them with a quick fix for each. If a result looks too good to be true, check these first.
| Mistake | What goes wrong | Fix |
|---|---|---|
| Mixing watts with joules | The ratio has no meaning | Convert both to one unit first |
| Putting input on top | The result is above 100 percent | Divide output by input |
| Using 75 instead of 0.75 | Answers come out 100 times too big | Use decimals in formulas |
| Skipping a stage | A chain looks better than it is | Multiply every stage |
| Expecting over 100 percent | One conversion cannot do that | Recheck values or think COP |
| Using Celsius in Carnot | The limit comes out wrong | Convert to kelvin first |
Enter any two values in the efficiency calculator to solve the third and see the energy wasted.
FAQs About Calculating Efficiency
How do you calculate efficiency as a percentage?
Divide the useful output by the total input, then multiply by 100. For example, 900 W out from 1,200 W in gives 0.75, or 75 percent.
Can efficiency be more than 100 percent?
Not for a single energy conversion. Efficiency runs from 0 to 1, or 0 to 100 percent. A heat pump can show a number above 1 because that figure is COP, a different measure.
How do you find the input from efficiency and output?
Divide the useful output by the efficiency as a decimal. A machine that is 80 percent efficient and must deliver 600 W needs 600 / 0.80 = 750 W of input.
How do you find the wasted energy?
Subtract the useful output from the total input. In the motor example, 1,200 W minus 900 W leaves 300 W of wasted power.
How do you find the total efficiency of several stages?
Multiply the efficiency of each stage as a decimal. Example stages of 0.90, 0.80, and 0.95 give 0.684, or 68.4 percent, for the whole chain.
What is the Carnot efficiency formula?
It is (hot temperature – cold temperature) / hot temperature, with both in kelvin. A hot side of 500 K and a cold side of 300 K give 0.40, or 40 percent, as the maximum.
Why do heat pumps show numbers above 100 percent?
They report COP, not efficiency. COP is useful heating or cooling divided by the work used. Heat pumps move existing heat, so their COP usually exceeds 1.
Sources and Further Reading
References Used in This Article
- fueleconomy.gov (US DOE and EPA), Where the Energy Goes: Gasoline Vehicles, accessed 2026-10-15.
- fueleconomy.gov (US DOE and EPA), Where the Energy Goes: Electric Cars, accessed 2026-10-15.
- HyperPhysics (Georgia State University), Carnot Cycle, accessed 2026-10-15.
- Wikipedia, Energy conversion efficiency (definition only), accessed 2026-10-15.
- Wikipedia, Coefficient of performance, accessed 2026-10-15.
This article is general science education. Real devices vary, so use the figures from your own equipment’s data sheet. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-10-15.
Author
Shakeel is the Founder and Editor-in-Chief of MultiCalculators.com, with over 15 years of experience in digital publishing and online tool development. He oversees editorial quality, formula accuracy, and usability to ensure the platform delivers reliable, practical calculators for users worldwide.




