How Much Polyurea Coating Do You Need?

Why does a five-gallon kit sometimes run out before the floor is finished? The answer is thickness. A thin film stretches a gallon across a huge area, and a thick film barely covers a closet.

Quick Answer

One US gallon of coating at 100 percent volume solids covers about 1,604 square feet at 1 mil dry thickness. Divide 1,604 by your dry mils to get coverage per gallon. Multiply by the volume solids fraction if it is below 100 percent. Then add a loss allowance and round up to whole kits.

Where Coverage Per Gallon Comes From

Coverage per gallon is plain geometry. A US gallon is legally defined as exactly 231 cubic inches. If you spread that volume into a flat film, the thickness decides how far it goes. Need a refresher on units? See how many cups are in a gallon.

Take a film 1 mil thick, which is 0.001 inch. Divide 231 cubic inches by 0.001 inch to get 231,000 square inches. Then divide by 144 square inches per square foot. The result is 1,604.17 square feet.

From one gallon to square feet at 1 mil A left to right flow of three boxes joined by arrows. The first box is one US gallon, 231 cubic inches. The second box is a film 0.001 inch thick covering 231,000 square inches. The third box divides by 144 to give 1,604.17 square feet. One gallon spread into a 1 mil film 1 US gallon 231 cubic inches Film 0.001 in thick 231,000 sq in Divide by 144 1,604.17 sq ft At 100 percent volume solids and 1 mil of dry thickness.
A gallon covers 1,604.17 square feet when spread 1 mil thick.

Polyurea is an elastomer made from an isocyanate component and an amine component. The geometry ignores the chemistry, though. The same math works for any liquid coating whose data sheet lists volume solids. Our polyurea calculator runs these steps for you.

Mils, Microns, and Volume Solids Explained

A mil is one thousandth of an inch. NIST lists 1 mil as 25.4 micrometers, so a 20 mil film is 508 microns. Data sheets use one unit or the other, so confirm which before you calculate. Our metric vs imperial guide helps with the switch.

Volume solids is the share of the wet liquid that stays behind as a dry film. At 100 percent, the dry film equals the wet film. At 80 percent, only 80 percent of the wet volume remains. Coverage falls to match, so 1 mil then covers 1,283 square feet per gallon.

Three formulas cover every case in this guide:

  • Coverage (sq ft per gallon) = 1,604.17 × solids / dry mils
  • Gallons = area / coverage × (1 + loss)
  • Metric (sq m per liter) = 1,000 × solids / microns

Solids is a decimal, so 95 percent is 0.95. The metric rule works because 1 liter spread 1 micron thick covers exactly 1,000 square meters.

Coverage at Common Thicknesses

Coverage drops in direct proportion to thickness. Double the film and each gallon covers half the area. The table shows four sample thicknesses at 100 percent volume solids.

Coverage per gallon at 100 percent volume solids
Dry thickness In microns Sq ft per gallon Gallons per 1,000 sq ft
20 mils 508 80.2 12.47
30 mils 762 53.5 18.70
60 mils 1,524 26.7 37.40
125 mils 3,175 12.8 77.92
Coverage per gallon falls as film thickness rises Four bars show square feet covered by one gallon at 100 percent volume solids. A 20 mil film covers 80.2 square feet. A 30 mil film covers 53.5. A 60 mil film covers 26.7. A 125 mil film covers 12.8. Thicker films give shorter bars. Square feet per gallon, by dry thickness 80.2 53.5 26.7 12.8 20 mils 30 mils 60 mils 125 mils
Thicker films give shorter bars, because each gallon spreads over less area.

Use the table as a quick sanity check. A 1,000 square foot floor at 30 mils needs about 18.70 gallons before loss. The same floor at 60 mils needs 37.40 gallons, exactly double. If your own result looks far from these ratios, recheck your units and your solids value.

At 80 percent solids, every coverage figure above drops by 20 percent. Plan on buying more material, not less, once solids fall below 100 percent.

Worked Example: A 500 Square Foot Floor

Say you need 30 mils over 500 square feet. The product is 100 percent solids and you allow 10 percent for loss. The loss figure is your own estimate. It is not a standard.

  1. Find coverage. 1,604.17 / 30 = 53.47 square feet per gallon.
  2. Find the net need. 500 / 53.47 = 9.35 gallons.
  3. Add the loss. Ten percent more brings it to 10.29 gallons.
  4. Round to kits. A 5 gallon kit means 3 kits, or 15 gallons. That leaves 4.71 gallons spare.
  5. Price it. At an example price of $100 a gallon (not a quote), 15 gallons is $1,500.00. That works out to $3.00 per square foot.
Net need, loss allowance, and spare in 15 gallons One horizontal bar shows the 15 gallons in three 5 gallon kits. The first and largest part is the net need of 9.35 gallons. The next small part is the loss allowance of 0.94 gallons. The last part is 4.71 gallons left spare. You buy 15 gallons to apply 10.29 Net 9.35 gal 0.94 Spare 4.71 gal Net need Loss allowance 0.94 gal Spare in the kits Example only: 500 sq ft at 30 mils, 100 percent solids, three 5 gallon kits.
Fixed kit sizes mean you often buy more than the calculated need.

Epoxy buyers face the same kit rounding, as our garage floor epoxy coverage guide shows.

Three More Worked Examples

Each case below changes one input: the shape, the solids, or the unit system.

  • Road line. A 1,000 foot line, 4 inches wide, at 20 mils. Four inches is 1/3 foot, so the area is 333.33 square feet. Coverage is 80.21 square feet per gallon. That gives 4.16 gallons. Add 5 percent loss for 4.36 gallons, which is one 5 gallon kit with 0.64 spare.
  • 95 percent solids. A 1,000 square foot area at 20 dry mils. Coverage is 1,604.17 × 0.95 / 20 = 76.20 square feet per gallon. Net need is 13.12 gallons. Spray 20 / 0.95 = 21.1 mils wet to leave 20 dry. With 10 percent loss you need 14.44 gallons, so three kits with 0.56 spare.
  • Metric tank. A 500 square meter tank at 500 microns. One liter covers 1,000 / 500 = 2 square meters. Net need is 250 liters. With 15 percent loss, that is 287.50 liters. Using an example kit of 200 liters, you buy 2 kits with 112.5 liters spare.

Minimum Thickness Rules and Real-World Coverage

Specifications set minimum thickness, and one public example shows how. The North Carolina Department of Transportation requires polyurea pavement marking lines to have at least 20 mils dry thickness on concrete and asphalt. It requires 30 mils on textured surfaces such as OGFC, and over a removed marking.

Those are one state agency’s rules for road markings. They are not rules for floors or tanks, and your own specification governs. Still, they show the cost. The 1,000 foot line above needs 6.23 gallons at 30 mils (333.33 / 53.47) before any loss, up from 4.16 at 20 mils.

Real coverage is lower than the math for practical reasons. Surface texture and porosity can hold extra coating. Overspray and equipment loss waste some. Crews also spray above the minimum so the thinnest spot still passes. The loss allowance covers these, and you choose it yourself.

Common Coverage Mistakes to Avoid

Most shortfalls come from a few repeat errors. Check your plan against this list.

  • Mixing mils and microns. One mil is 25.4 microns, so a swap changes the answer by about 25 times.
  • Forgetting volume solids. A product below 100 percent covers less than the base figure.
  • Using wet thickness when the spec says dry. Convert with dry mils divided by solids.
  • Skipping the loss allowance. The net figure is a floor, not a shopping list.
  • Buying exact gallons. Kits come in fixed sizes, so round up.
  • Forgetting other layers. Primer and topcoat are separate runs, each with its own calculation.
  • Treating the minimum as the target. A minimum is the thinnest spot allowed, not your average film.

If your project also uses two-part resins, our epoxy resin mix ratio guide covers the ratio side of the job.

Ready to run your own numbers?

Enter your area, thickness, solids, loss, and kit size in the polyurea coverage calculator to see gallons and kits in seconds.

FAQs About Polyurea Coverage

How many square feet does one gallon of polyurea cover?

At 100 percent volume solids, one gallon covers about 80.2 square feet at 20 mils. Divide 1,604.17 by your dry mils to find coverage at any other thickness.

How many mils is 500 microns?

About 19.7 mils. One mil equals 25.4 microns, so divide 500 by 25.4. Always check whether your data sheet lists mils or microns before you calculate.

What is the difference between wet and dry mils?

Wet mils are the film as sprayed. Dry mils are what remains. Wet mils equal dry mils divided by the solids fraction, so 20 dry mils at 95 percent solids needs about 21.1 wet mils.

Why does volume solids change how much I need?

Only the solid share of the liquid stays on the surface. At 80 percent solids, 1 mil covers 1,283 square feet per gallon instead of 1,604, so coverage falls 20 percent.

How much loss allowance should I add?

There is no published standard figure. The examples here use 5, 10, and 15 percent as planning estimates. Choose your own based on surface texture, overspray, and equipment.

What is the minimum thickness for polyurea road markings?

One state agency, NCDOT, sets 20 mils dry on concrete and asphalt, and 30 mils on textured surfaces. That covers road markings only. Your own specification governs other work.

Does this math work for other coatings?

Yes, for any liquid coating whose data sheet lists volume solids. A gallon is 231 cubic inches either way. Thickness limits differ by product, so follow the data sheet.

Sources and Further Reading

References Used in This Article

This article is a planning guide. Follow your product data sheet and project specification for thickness, preparation and the final quantity. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-10-15.


Author

shakeel-Muzaffar
Founder & Editor-in-Chief at  ~ Web ~ More Posts

Shakeel is the Founder and Editor-in-Chief of MultiCalculators.com, with over 15 years of experience in digital publishing and online tool development. He oversees editorial quality, formula accuracy, and usability to ensure the platform delivers reliable, practical calculators for users worldwide.