How to Estimate Bricks for a Wall

How many bricks does a 20 ft x 8 ft wall need after you leave out a door? The answer is 1,049 bricks with a 10 percent waste allowance, plus 8 bags of mortar. Four short steps in this guide lead you to that number.

Quick Answer

Net wall area is length times height minus the doors and windows. Multiply that area by 6.86 bricks per square foot for a standard modular brick with a 3/8-inch joint. Then add a waste allowance and round up. Plan about 7 mortar bags for every 1,000 modular bricks. These are planning figures, so confirm your actual brick size.

Why Brick Counts Start With Wall Area

Every brick estimate starts with the visible face of the wall, measured in square feet. You count the surface that shows, not the depth of the wall or the number of courses. Brick Industry Association Technical Note 10 covers this method under the title “Dimensioning and Estimating Brick Masonry.”

Multiply the length of the wall by its height to get the gross area in square feet. A wall 20 ft long and 8 ft high has a gross area of 160 square feet. Repeat the step for every wall in the job, then add the areas together.

Area comes first because brick sizes tie directly to face area. Once you know the area, a single factor turns it into a brick count. The square footage calculator handles the length-times-height step for rooms and walls.

Subtracting Doors and Windows

Doors and windows leave gaps in the wall, and no brick fills those gaps. Subtract the area of each opening from the gross area. The result is the net area, which is the surface that brick really covers.

Measure every opening the same way, as width times height. A door of 3 ft x 7 ft covers 21 square feet. Take 21 from the gross 160, and the net area is 139 square feet.

Walls with several openings need one extra step to stay accurate. Add all the opening areas together first, then subtract the total once. This keeps the arithmetic short and easy to recheck. For related area work on interior surfaces, the drywall calculator is a useful companion.

Gross wall area minus an opening equals net area One long navy bar shows 139 square feet of net brick area. A short amber bar beside it shows the 21 square foot door opening. Together the two bars make the 160 square foot gross wall. Gross area minus the door equals net area Gross wall: 160 sq ft 20 ft x 8 ft = 160 sq ft Split into door and brick area Net brick area: 139 sq ft Door 21
A 3 ft x 7 ft door takes 21 square feet from a 160 square foot wall.

The Bricks-Per-Square-Foot Factor

A standard modular brick has a nominal face of 8 inches long and 2.25 inches high. Laid with a 3/8-inch mortar joint, it covers about 6.86 bricks per square foot of wall face. The Brick Industry Association publishes this kind of coverage guidance.

Some estimating tables round the factor to 7 bricks per square foot. The 6.86 figure is the one for a standard modular brick with a 3/8-inch joint. Rounding to 7 raises the count by about 2 percent.

Other brick sizes use a different factor than the modular figure. A larger brick covers more wall per unit, so fewer pieces fill the same area. Ask your supplier for the nominal face size and joint thickness before you trust any factor.

The tool uses 6.86, and the whole method rests on that one number. Net area times the factor gives the base brick count before any waste. Keep the factor and the brick size matched, because a mismatch spoils the total.

For the example wall, 139 square feet times 6.86 gives 953.54 bricks. The next section adds the waste allowance to that base figure. Joint thickness matters here too, since the 6.86 factor assumes a 3/8-inch joint.

Adding Waste to the Count

Bricks chip in transit, and cuts at corners and openings leave offcuts. Every order needs a waste allowance on top of the base count. About 10 percent is common practice, but it is a planning allowance and not a fixed standard.

Apply it by multiplying the base count by 1 plus the waste percent divided by 100. For a 10 percent allowance, the multiplier is exactly 1.10. Round the answer up, because you cannot buy part of a brick.

The chart shows the 139 square foot wall at three waste levels. Waste depends on cuts and breakage, so a wall with many cuts needs a larger allowance. Pick your own figure, then confirm it with your supplier. A tidy wall with few openings needs less waste than a busy one.

Bricks needed for a 139 square foot wall at three waste levels Three horizontal bars drawn to one scale. The teal bar for no waste is 954 bricks. The navy bar for 5 percent waste is 1,002 bricks. The amber bar for 10 percent waste is 1,049 bricks. Bricks for 139 sq ft at 6.86 per sq ft 0% waste 954 5% waste 1,002 10% waste 1,049 Each bar rounds up to a whole brick.
Waste moves the count from 954 to 1,049 bricks on the same wall.

Estimating Mortar Bags

A common estimating rule is about 7 bags of mortar for every 1,000 modular bricks. Georgia Masonry Supply lists this figure in its rule-of-thumb estimating sheet. The count varies by brick size, with more bags needed for larger brick.

The tool follows a simple formula for the mortar count. Mortar bags equal total bricks divided by 1,000, times 7, rounded up. You round up because a partial bag cannot be bought at the store.

For 1,049 bricks, the math is 1,049 / 1000 x 7, which gives 7.3. That figure rounds up to 8 bags of mortar. Use the total after waste, since the extra bricks get laid too.

Joint thickness changes mortar use, and so does how much mortar you waste at the board. Treat the bag count as a planning starting point for your order. Check the coverage printed on the bag your supplier sells.

A Full Worked Example

Take the wall 20 ft long and 8 ft high with one 3 ft x 7 ft door. Each step below matches the method the brick calculator uses. The table lists every calculation in the order you would run it.

Brick estimate for a 20 ft x 8 ft wall with one door
Step Calculation Result
1. Gross area 20 x 8 160 sq ft
2. Door area 3 x 7 21 sq ft
3. Net area 160 – 21 139 sq ft
4. Bricks before waste 139 x 6.86 953.5, rounds to 954
5. Bricks with 10% waste 139 x 6.86 x 1.10 1,049 bricks
6. Mortar bags 1,049 / 1000 x 7 7.3, rounds up to 8 bags

The tool keeps the decimals until the last step, so it rounds only once. In step 5, 953.54 x 1.10 gives 1,048.9, which rounds up to 1,049. Rounding step 4 first and then adding waste would give 1,050 instead.

That one-brick gap shows why the order of rounding matters. Neither answer changes the plan in any real way, because both figures sit inside the allowance you chose. Round once at the end, and keep your notes in the same order as the table.

From net area to brick count Four boxes in a row joined by operator signs. The teal box is 139 square feet of net area. The navy box is the factor 6.86 bricks per square foot. The amber box is the waste multiplier 1.10. The final navy box is the result, 1,049 bricks. One wall, three numbers, one count 139 sq ft net x 6.86 bricks per sq ft x 1.10 10% waste = 1,049 bricks The tool rounds up once, at the end, to a whole brick.
Net area times 6.86 times 1.10 gives 1,049 bricks for the example wall.

Limits of a Brick Estimate

The method is simple, and the limits sit around it. Read the list below as a checklist for where your own check is needed. This article covers the count only, not bricklaying technique, footings or structural design.

  • Brick sizes vary from one supplier to another. The 6.86 factor fits a standard modular brick, so confirm your actual brick size before you order.
  • Joint thickness changes the brick count. A thicker or thinner joint than 3/8 inch shifts both the bricks and the mortar you need.
  • Waste depends on how many cuts and breaks occur. Add your own allowance for the wall, and share it with your supplier.
  • The mortar figure is only a rule of thumb. The figure of about 7 bags per 1,000 modular bricks varies with brick size.

The figures here are planning estimates, not a precise order. Verify your plan against local building codes before you buy. For other estimating jobs around the house, browse the construction calculators.

Ready to check your own wall?

Enter your wall size and waste in the brick calculator to see the brick count and mortar bags for your wall.

FAQs About Estimating Bricks

How many bricks are in a square foot of wall?

A standard modular brick laid with a 3/8-inch mortar joint covers about 6.86 bricks per square foot. Some estimating tables round that factor up to 7 bricks per square foot.

How do I find the net wall area?

Multiply the wall length by its height, then subtract the area of doors and windows. A 20 ft x 8 ft wall with a 3 ft x 7 ft door has 160 – 21 = 139 square feet.

How many bricks does a 20 ft x 8 ft wall with one door need?

It needs 1,049 bricks with a 10 percent waste allowance. The net area is 139 square feet, and 139 x 6.86 x 1.10 rounds up to 1,049.

How much waste should I add to a brick order?

About 10 percent is common practice, but it is a planning allowance and not a fixed standard. Waste depends on cuts and breakage, so choose your own figure.

How many bags of mortar do I need per 1,000 bricks?

A common rule is about 7 bags per 1,000 modular bricks, and the count varies by brick size. For 1,049 bricks, the tool gives 7.3, which rounds up to 8 bags.

Does brick size change the count?

Yes. Different brick sizes use a different bricks-per-square-foot factor, and joint thickness shifts the count too. Confirm the nominal size with your supplier.

Is the estimate exact enough to place an order?

No. It is a planning estimate. Confirm your actual brick size, add your own waste allowance, and verify the plan against local building codes.

Sources and Further Reading

References Used in This Article

The tool multiplies your net wall area by a bricks-per-square-foot factor, adds waste, and estimates mortar bags. Brick sizes and joints vary, so confirm your actual brick size and add waste before you order. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-11-22.


Author

shakeel-Muzaffar
Founder & Editor-in-Chief at  ~ Web ~ More Posts

Shakeel is the Founder and Editor-in-Chief of MultiCalculators.com, with over 15 years of experience in digital publishing and online tool development. He oversees editorial quality, formula accuracy, and usability to ensure the platform delivers reliable, practical calculators for users worldwide.