How can one small shower need 2.24 gallons of liquid membrane, or 4.93? The area stays the same. What changes is the job the membrane must do, and that one choice can more than double your order.
The amount of shower membrane you need depends on the rate for the job, not just the area. For RedGard, two coats at the ANSI A118.10 shower rate need 40 square feet per gallon in total. Add up floor, walls and extras, add an allowance, divide by that rate, then round up to whole pails.
Why Coverage Depends on the Job
RedGard has no single coverage number. The data sheet gives a rate for each purpose, and every rate is per coat. A lower number of square feet per gallon means a thicker coat, so you need more product.
For general waterproofing, apply 110 square feet per gallon in each coat. For ANSI A118.10 shower-pan type work, the sheet calls for two coats at 80 each. For crack isolation under ANSI A118.12, it calls for two coats at 50 each. As a vapor barrier over concrete, the rate is 70 per coat.
| Purpose | Rate per coat (sq ft per gallon) | Coats | All coats together (sq ft per gallon) |
|---|---|---|---|
| General waterproofing | 110 | 2 | 55 |
| ANSI A118.10 shower-pan type work | 80 | 2 | 40 |
| ANSI A118.12 crack isolation | 50 | 2 | 25 |
A roller or brush needs a minimum of two coats so the film stays continuous. That is why the last column matters most when you order. Other brands publish their own rates, so never reuse these numbers for a different product.
Counting the Wet Area Step by Step
Start with the surfaces you will coat. Your tile count uses many of the same measurements, so the tile calculator can share the same floor and wall numbers. The coated area has four parts:
- Floor: length times width of the shower base.
- Walls: total wall run times the height you will coat.
- Extras: the surfaces of a curb, bench or niche.
- Openings: subtract any area you will not coat.
Wall run means the combined length of every coated wall. In our example, three walls run 5, 3 and 5 feet, so the run is 13 feet. Measure each wall at the height you plan to coat, because that height is your own project choice. This example uses 7 feet.
Small extras add up fast. A curb has a top and two faces, and a niche has a back and four sides. Write each one down instead of guessing, then subtract any opening you leave bare.
Turning Square Feet Into Gallons
Gallons come from one short formula. Take the wet area, add your allowance, and divide by the coverage for all coats together. The data sheet does not publish an allowance, so that percentage is your own planning choice.
- Find the all-coats rate. Divide the per-coat rate by the number of coats. Two coats at 80 square feet per gallon cover 40 square feet per gallon in total.
- Add your allowance. Multiply the wet area by 1.10 if you choose a 10 percent example cushion.
- Divide and round up. Divide that area by the all-coats rate to get gallons, then round up to whole pails.
RedGard comes in a 1 gallon pail, listed at a nominal 100 square feet, and a 3.5 gallon pail, listed at 350. Those listed figures are nominal. Your own job rate decides how far a pail really goes.
You can skip the hand math with our shower waterproofing calculator, which follows this same formula.
A Worked Example: A 5 by 3 Foot Shower
Take a 5 by 3 foot shower with three walls coated to 7 feet. The floor is 15 square feet. The walls are 13 times 7, or 91. A curb and niche add 6, so the area is 15 plus 91 plus 6, or 112 square feet. With a 10 percent example allowance, that becomes 123.2.
Now divide by the all-coats rate for each purpose. At the general rate of 55, you need 123.2 / 55, or 2.24 gallons. At the shower rate of 40, you need 3.08 gallons, which fits in one 3.5 gallon pail with 0.42 gallons left. At the crack isolation rate of 25, you need 4.93 gallons, which is more than one pail. Two 3.5 gallon pails would cover it.
Checking Wet Film Thickness
Each rate also sets how thick one wet coat is. The data sheet says no coat should exceed 40 mils of wet film. A mil is one thousandth of an inch.
You can work it out yourself. One gallon is 231 cubic inches, and one square foot is 144 square inches. That gives wet film in mils as 1,604 divided by the square feet per gallon in a coat. At 80, the coat is about 20.1 mils.
Why does thickness matter to a buyer? Because it is the reason the rates differ. A thicker coat uses more gallons for the same area, and a thinner coat stretches the pail further. The sheet balances that trade by setting a rate for each purpose.
The same math shows the limit in reverse. Spreading a coat below about 40 square feet per gallon would pass 40 mils. So do not pour on one thick coat to save a pass.
Common Ordering Mistakes to Avoid
Most short orders come from a few repeat errors. Each one is easy to fix before you buy.
- Using one rate for every job. A shower pan, a crack isolation layer and a general barrier each have a different rate. Pick the one that matches your purpose.
- Counting only the floor. Walls often make up most of the area. In our example, they are 91 of 112 square feet.
- Dividing by the per-coat rate. The per-coat rate covers one coat. For two coats, divide it by two first.
- Trusting the nominal pail figure. The listed 100 and 350 square feet are nominal. Your job rate sets the real coverage.
- Skipping the allowance. Running out halfway through a coat leaves a seam. Add a cushion you are comfortable with.
Pails, Coats and Drying Time
Always order by whole pails. In the shower example, 3.08 gallons rounds up to one 3.5 gallon pail. If a number lands just over a pail, add a small 1 gallon pail instead of risking a short second coat.
Apply the second coat at right angles to the first. That crossing pattern helps close any thin spots. RedGard typically dries in 1 to 1.5 hours per coat, and it takes 1 to 1.5 hours to turn completely red as it dries.
Once the membrane is done, tile and grout come next. Our guide on how much grout you need for tile covers that step. The same area-over-coverage idea appears in the paint coverage calculator, but always use the membrane’s own data sheet rates.
Enter your floor, wall run, height and extras in the shower waterproofing calculator to get gallons and pails in seconds.
FAQs About Shower Waterproofing Membrane
How many coats of RedGard does a shower need?
The data sheet requires a minimum of two coats when you use a roller or brush, so the film stays continuous. Apply the second coat at right angles to the first.
What coverage should I use for a shower pan?
For ANSI A118.10 shower-pan type work, the RedGard sheet calls for two coats at 80 square feet per gallon each. That is 40 square feet per gallon for both coats together.
Does a 1 gallon pail really cover 100 square feet?
That is the listed nominal figure. Your job rate sets real coverage. At the shower rate, two coats cover only 40 square feet per gallon, so one gallon covers far less than 100.
How thick should each coat be?
No coat should exceed 40 mils of wet film. The shower rate of 80 square feet per gallon works out to about 20.1 mils per coat, well under that limit.
How long should I wait between coats?
RedGard typically dries in 1 to 1.5 hours per coat, and it turns completely red as it dries. Check the current data sheet for your jobsite before you apply the next coat.
How much extra membrane should I add?
Data sheets do not publish an allowance. This article uses 10 percent only as an example. The cushion is your own planning choice, so pick one that fits your surfaces and skill.
Can I use these rates for other brands?
No. These are RedGard figures from one data sheet. Other brands publish their own coverage rates, coat counts and limits, so use the data sheet for the product you actually buy.
Sources and Further Reading
References Used in This Article
- Custom Building Products, RedGard Waterproofing and Crack Prevention Membrane, data sheet TDS-104 (02/14/2025), accessed 2026-10-13.
- Wikipedia, Waterproofing (background), accessed 2026-10-13.
- Wikipedia, Thousandth of an inch, the mil unit (background), accessed 2026-10-13.
This article is general education, not installation advice. Follow the membrane data sheet and your local code for coats, curing and testing. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-10-13.
Author
Shakeel Muzaffar is the Founder and Editor-in-Chief of MultiCalculators.com, bringing over 15 years of experience in digital publishing, product strategy, and online tool development. He leads the platform's editorial vision, ensuring every calculator meets strict standards for accuracy, usability, and real-world value. Shakeel personally oversees content quality, formula verification workflows, and the platform's commitment to publishing tools that are genuinely useful for students, professionals, and everyday users worldwide.




