How Many Pavers Do You Need? Count, Base Gravel and Sand

Standing in the paver aisle, how do you know if you need 450 pavers or 495? A 10 by 10 foot patio of small 4 by 8 inch pavers takes about 495. Those extra 45 are not a mistake. This guide shows how to count them, plus the gravel and sand under them.

Quick Answer

To count pavers, divide the project area by the area of one paver. Then add waste (10 percent for a straight lay, 15 percent for curves or herringbone). A 100 square foot patio of 4 by 8 inch pavers needs about 495. Base gravel and bedding sand come from area times depth.

Count Pavers From Area, Not by Eye

Counting pavers takes three steps and one multiplication. You work in square feet, so every measurement ends up in the same unit. The steps work for any rectangle.

  1. Find the project area. Multiply length by width in feet. For an L shape, split it into simple pieces and add them. Our square footage calculator handles that part.
  2. Find the area of one paver. Multiply its length by its width in inches, then divide by 144 to get square feet.
  3. Divide and add waste. Divide the project area by one paver’s area, multiply by 1 plus the waste rate, and round up to a whole paver.

Waste covers edge cuts and a few broken units. The paver calculator assumes 10 percent for a straight lay and 15 percent for curves or herringbone. Those rates are planning defaults, not a published standard.

Joint width does not enter the math. Joints are only 1/16 to 3/16 inch wide, so ignoring them changes the count very little.

Worked Example: A 10 by 10 Foot Patio

Take a 10 by 10 foot patio laid with 4 by 8 inch pavers in a straight pattern. Here is the full count, one step at a time.

  1. Project area. 10 x 10 = 100 square feet.
  2. One paver. 4 x 8 = 32 square inches, and 32 / 144 = 0.2222 square feet.
  3. Net count. 100 / 0.2222 = 450 pavers.
  4. Add 10 percent waste. 450 x 1.10 = 495 pavers.

The paver calculator also shows 495. Keep a few extra pavers from the same batch as spares.

Now switch to a curved or herringbone layout. At 15 percent waste, 450 x 1.15 = 517.5, so you would buy 518. You can check your own total with the paver calculator, which also lists gravel, sand and edge restraint.

Keep the roles straight when you shop. The 450 net pavers cover the area itself. The extra 45 are for edge cuts and breakage, so you are not left short on the last row.

How Paver Size Changes the Count

Bigger pavers mean fewer pieces, but the area stays the same. The chart shows four common sizes covering the same 100 square feet. Check the size before you compare prices per paver.

Paver count by paver size for 100 square feet Four horizontal bars for a 100 square foot patio with 10 percent waste. A 4 by 8 inch paver needs 495. A 6 by 6 inch paver needs 440. A 6 by 9 inch paver needs 294. A 12 by 12 inch paver needs 110. Bigger pavers mean fewer pieces for the same area. Pavers to buy for 100 sq ft, with 10 percent waste 4 x 8 in 0.22 sq ft each 6 x 6 in 0.25 sq ft each 6 x 9 in 0.375 sq ft each 12 x 12 in 1 sq ft each 495 440 294 110 Same 100 sq ft, straight lay, counts rounded up to whole pavers. Example only.
Same 100 square feet, four paver sizes, four very different counts.

A 6 by 9 inch paver covers 0.375 square feet, so 100 square feet needs 266.7 net. With 10 percent waste that is 293.3, and you buy 294. Always round up, never down. Round only once, at the very end, after you add the waste.

Size does not change the thickness rule. ICPI Tech Spec 10 calls for pavers at least 2 3/8 inches (60 mm) thick in pedestrian areas and residential driveways. For driveways, CMHA adds a maximum 4:1 aspect ratio.

Base Gravel and Bedding Sand Volumes

Both layers use the same formula. Take area times depth in inches, divide by 12 to get feet, then divide by 27 to get cubic yards. ICPI Tech Spec 10 gives a minimum aggregate base of 4 to 6 inches under walks, depending on soil and loads. Bedding sand is spread and screeded to a nominal 1 inch.

For our 100 square foot patio at a 4 inch base: 100 x 4 / 12 / 27 = 1.235 cubic yards of gravel. For 1 inch of sand: 100 x 1 / 12 / 27 = 0.309 cubic yards. Our gravel calculator and sand calculator help you turn those volumes into an order.

Material volumes for 100 square feet by project type (calculator defaults)
Layer Patio Driveway
Base depth 4 in 6 in
Base gravel 1.235 cu yd 1.852 cu yd
Bedding sand (1 in) 0.309 cu yd 0.309 cu yd
Paver thickness 2 3/8 in minimum 2 3/8 in minimum

Those are volumes for the paver footprint only. Your base will run wider than that, as the next section explains.

Layer Order, Joints and Edge Restraint

A paver surface is a stack of layers, and each one has a job. From the bottom, you have compacted soil, a compacted aggregate base, about 1 inch of bedding sand, and the pavers. The diagram shows the order, not the true scale.

The layers under a paver patio A side view, not to scale. From top to bottom: pavers at least 2 3/8 inches thick with narrow joints between them, about 1 inch of bedding sand, a compacted aggregate base of 4 to 6 inches, and compacted soil subgrade. An edge restraint stands at the side of the pavers and sand, and the base extends past it. The layers under a paver patio, top to bottom Joints between pavers: 1/16 to 3/16 in Compacted to 98 percent Compacted to 98 percent Pavers 2 3/8 in minimum Bedding sand 1 in nominal Aggregate base 4 in patio, 6 in drive Soil subgrade dug and compacted Edge restraint Not to scale. Depths are minimums or planning defaults; your site may need more.
Four layers plus an edge restraint. Each layer is compacted or screeded before the next goes on.

Joints are sand-filled gaps of 1/16 to 3/16 inch. Joint sand is swept in and compacted until the joints are full. Coverage depends on the product and joint width, so see our guide on how much polymeric sand for pavers. The calculator’s 5 bags for our patio is a rough default of 20 square feet per 50 pound bag.

Edge restraints run around the full perimeter of the pavers. Our patio needs 2 x (10 + 10) = 40 linear feet. With spiked restraints, the base must extend past the spikes, at least as far as the base is thick. A 4 inch base leaves 4 inches of base beyond the spikes, so you dig wider than the paver area.

Compaction, Finish Height and Tolerances

Compaction is the step people rush, and the specifications are firm about it. Both the soil subgrade and the aggregate base should reach at least 98 percent of standard Proctor density (ASTM D698). That applies to pedestrian areas and residential driveways.

  • Dig depth. Add the layers: 4 in base + 1 in sand + 2 3/8 in paver = 7 3/8 inches for our patio. A 6 inch driveway base makes it 9 3/8 inches.
  • Surface tolerance. The finished surface should stay within plus or minus 3/8 inch over 10 feet.
  • Lippage. Neighboring pavers should sit no more than 1/8 inch apart in height.
  • Settling allowance. Finish pavers about 1/8 to 1/4 inch above edges and drains.

The settling allowance exists because layers can compress a little over time. A surface that starts slightly high ends up level.

Driveways carry heavier loads, and the base thickness depends on your soil. Use a professional for any driveway, and check your local code before you dig.

Ready to count your own project?

Enter your size and paver dimensions in the paver calculator to get pavers, base gravel, sand and edge restraint in one pass.

FAQs About Paver Counts and Base Materials

How many pavers fit in one square foot?

Divide 144 by the paver’s area in square inches. A 4 by 8 inch paver is 32 square inches, so it takes 4.5 per square foot before waste. At 10 percent waste, plan on about 5.

How much extra should I order for waste?

The paver calculator uses 10 percent for a straight lay and 15 percent for curves or herringbone. These are planning estimates, not a published standard, so round up to whole pavers.

How thick should the gravel base be?

ICPI Tech Spec 10 gives a minimum of 4 to 6 inches of aggregate base under walks, depending on soil and loads. The calculator defaults to 4 inches for patios and 6 inches for driveways.

How thick is the bedding sand layer?

Spread and screed the bedding sand to a nominal 1 inch (25 mm). For 100 square feet, that is about 0.31 cubic yards of sand.

Do I need edge restraints on a patio?

Yes. Edge restraints go around the whole perimeter of the pavers on walks, patios and driveways. A 10 by 10 foot patio needs 40 linear feet of restraint.

How wide should the joints between pavers be?

Joints should be 1/16 to 3/16 inch (2 to 5 mm) wide. Sweep joint sand in and compact until the joints are full. The paver count math ignores joint width.

Can I use patio pavers on a driveway?

Only if they are thick enough. CMHA notes residential driveways need units at least 2 3/8 inches thick with a maximum 4:1 aspect ratio. Follow the paver maker’s instructions and hire a professional.

Sources and Further Reading

References Used in This Article

This article is general education, not engineering advice. Soil, climate and use vary, so follow your paver maker’s instructions and local code, and use a professional for driveways. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-10-13.


Author

shakeel-Muzaffar
Founder & Editor-in-Chief at  ~ Web ~ More Posts

Shakeel Muzaffar is the Founder and Editor-in-Chief of MultiCalculators.com, bringing over 15 years of experience in digital publishing, product strategy, and online tool development. He leads the platform's editorial vision, ensuring every calculator meets strict standards for accuracy, usability, and real-world value. Shakeel personally oversees content quality, formula verification workflows, and the platform's commitment to publishing tools that are genuinely useful for students, professionals, and everyday users worldwide.