Where does the rain go when your yard cannot soak it up? On a sloped lot, water often runs across the surface. It can pool against a fence, a patio or a wall, and a French drain gives it an easier path.
A French drain is a shallow trench that catches water moving across a slope and carries it away. It holds a perforated pipe, surrounded by gravel, wrapped in geotextile fabric. The trench should fall 0.5 to 1 percent, which is 0.06 to 0.12 inches per foot. It suits shallow yard problems, not major flooding.
What a French Drain Does and Does Not Do
A French drain is a shallow trench that intercepts water flowing across a slope. Inside the trench, a perforated plastic pipe sits in gravel. The pipe carries the water to a place where it can leave safely.
Delaware’s DNREC says the goal is to direct water away from a structure to reduce pooling and flooding. The outlet should reach a natural drainage site, such as a stream, swale, ditch or slope.
The drain has limits. DNREC warns that a simple French drain may not stop seepage into a basement or crawlspace. It is also not meant for high flooding, meaning times when the water table or flood water sits more than a few inches above the lowest floor.
In plain terms, the drain does not pull water out of the ground. It gives shallow water a path, and gravity does the moving. So the first questions are where the water comes from and where it can safely go.
The Layers Inside the Trench
A French drain has four working parts: fabric, gravel, pipe and a soil cap. Each part has one job. The fabric lines the trench, the gravel keeps open water paths, and the pipe carries the flow.
Skip the fabric and soil can fill the gaps between the stones. Skip the outlet plan and the water has nowhere to go. Perforated pipe, geotextile fabric and gravel are the three materials to price.
WSU Extension explains that the weed cloth or geotextile is wrapped over the top of the gravel, then covered with soil. This stops soil from filling the spaces between the stones.
At the outlet end, a T-shaped pipe slows the water and spreads it over a larger area. Downspouts can also be buried and tied into the drain. Our gutter calculator counts the downspouts a roof edge needs.
Slope: How Much Fall the Trench Needs
WSU Extension says the trench should slope between 0.5 percent and 1 percent. One percent means a one-foot drop over 100 feet. That works out to 0.12 inches of fall per foot of trench.
To find the fall for your own run, multiply its length in feet by 0.06 to 0.12 inches. A 30-foot run, for example, falls 1.8 to 3.6 inches.
Half a percent is 0.06 inches per foot. Over a 50-foot run, that is a 3-inch drop at 0.5 percent and a 6-inch drop at 1 percent. The drawing shows both.
These are small drops, so check the grade with a level or string line before you backfill. DNREC does not recommend a French drain where the yard lacks slope.
Where a French Drain Works and Where It Fails
A shallow yard drain is the sweet spot. DNREC says simple drains 8 to 24 inches deep can be a DIY job. Anything deeper, more complex, or close to the foundation calls for a drainage contractor. Before you dig, ask three questions: where does the water come from, where can it safely go, and is the site shallow enough for a DIY job?
| Situation | Fit | Who builds it |
|---|---|---|
| Shallow yard drain, 8 to 24 in deep | Good match | Homeowner, after checking permits and calling 811 |
| Deeper or complex drain | Needs design | Drainage contractor |
| Drain close to the foundation | Higher risk | Drainage contractor |
| Yard with little slope | Not recommended | Ask a pro about other options |
| High flood water above the lowest floor | Not suited | Ask a pro about other options |
WSU adds that French drains work best when they are not within the groundwater table. Keep heavy machinery and livestock off the trench, because compaction can crush the pipe. DNREC also warns that a poorly designed drain could raise the risk of flooding the foundation.
Estimating Gravel, Pipe and Fabric for 50 Feet
Material math is simple geometry. This example uses the defaults in our French drain calculator: a 12-inch-wide trench, 4-inch pipe, and 100 pounds per cubic foot of gravel. Those are planning assumptions, not standards.
- Trench volume. A 50-foot trench, 1 foot wide and 1.5 feet (18 inches) deep, is 50 x 1 x 1.5 = 75 cubic feet, or 2.78 cubic yards.
- Pipe volume. A 4-inch pipe has a radius of 1/6 foot. Pi x (1/6)^2 x 50 is about 4.36 cubic feet.
- Gravel. Subtract the pipe: 75 – 4.36 = 70.64 cubic feet. That is 2.62 cubic yards, or 3.53 tons at 100 pounds per cubic foot.
- Fabric. Bottom and both sides: 50 x (2 x 1.5 + 1) = 200 square feet. To wrap the top too, add about 12 inches of width, or 50 more square feet. That makes about 250.
- Pipe length. The pipe runs the full 50 feet of the drain.
Real stone weight varies, so confirm tons with your supplier. The gravel calculator can help with other stone types. Pipe hole size, stone size and trench width are not set in these sources, so follow the pipe maker’s instructions.
Cost, Permits and Yearly Upkeep
DNREC gives one cost example. Materials for a simple DIY drain, 8 to 24 inches deep and 60 linear feet long, run about $600 to $2,000. That is an estimate, and prices vary by place and by material.
Call 811 before you dig, and check your city or county for permits. WSU notes that moving more than 50 cubic yards of material may need a grading permit in Clark County, Washington. Our example trench is about 2.8 cubic yards, far below that mark, but local rules differ.
A drain that works well still needs care. Write down where the outlet is, since it is the first place to look if the yard stays wet.
- Monthly: clear debris, leaf litter and rodent nests.
- Yearly: confirm the drain works and does not cause pooling on neighboring properties.
If your yard problem sits behind a wall, the retaining wall calculator counts the drain-zone gravel and pipe for that job.
Enter your trench length, width, depth and pipe size in the French drain calculator to get gravel, pipe and fabric amounts in seconds.
FAQs About French Drains
What slope should a French drain have?
Between 0.5 and 1 percent, according to WSU Extension. That is a drop of 0.06 to 0.12 inches per foot, or 3 to 6 inches over a 50-foot run.
Do I need fabric around the gravel?
In the standard design, yes. WSU describes geotextile or weed cloth lining the trench and wrapping over the gravel. It stops soil from filling the spaces between the stones.
How deep is a DIY French drain?
DNREC says simple shallow yard drains 8 to 24 inches deep can be DIY. Deeper or complex drains, or drains close to the foundation, need a drainage contractor.
Will a French drain fix a wet basement?
Not always. DNREC says a simple French drain may not prevent seepage into a basement or crawlspace. A poorly designed one could even raise flood risk. Ask a drainage contractor.
Where should the drain water go?
To a natural drainage site such as a stream, swale, ditch or slope, per DNREC. A T-shaped pipe at the outlet slows the water and spreads it over a larger area.
How much gravel does a 50-foot drain need?
With a 12 by 18 inch trench and 4-inch pipe, about 2.62 cubic yards, or 3.53 tons at 100 pounds per cubic foot. Real stone weight varies, so confirm with your supplier.
Do I need a permit or an 811 call?
Call 811 before you dig, and check your city or county for permits. WSU notes a grading permit may apply above 50 cubic yards in Clark County, Washington. Local rules differ.
Sources and Further Reading
References Used in This Article
- Washington State University Extension, Clark County, French drains, accessed 2026-10-13.
- Delaware DNREC, I-ADAPT, French Drain for Yard (fact sheet), accessed 2026-10-13.
- Wikipedia, French drain (background reading), accessed 2026-10-13.
This article is general education, not engineering advice. Drainage problems depend on your soil and site, so ask a drainage contractor or your local building office before you dig. Reviewed for accuracy by Prof. Dr. Khalil Mudassar, PhD. Last updated 2026-10-13.
Author
Shakeel Muzaffar is the Founder and Editor-in-Chief of MultiCalculators.com, bringing over 15 years of experience in digital publishing, product strategy, and online tool development. He leads the platform's editorial vision, ensuring every calculator meets strict standards for accuracy, usability, and real-world value. Shakeel personally oversees content quality, formula verification workflows, and the platform's commitment to publishing tools that are genuinely useful for students, professionals, and everyday users worldwide.




