A pool volume calculator finds the water your pool holds in gallons and liters from its shape and dimensions. A 30 x 15 ft rectangular pool averaging 6 ft deep holds about 20,197 gallons (76,455 liters). Enter the length, width and depth for a rectangular, round, oval or freeform pool to get the volume, fill time and chemical startup estimates. Always verify measurements on-site.
Volume (gallons)
Calculations run in your browser. Inputs are not sent to our servers; anything you Save stays in this browser only.
Saved results (0)
How to Use the Pool Volume Calculator
- Select the pool shape: rectangle, round, oval or freeform (kidney).
- Choose imperial (feet) or metric (meters) for your dimensions.
- Enter the length (or diameter for round pools) and width.
- Enter the shallow-end and deep-end depths. For a flat-bottom pool use the same value for both.
- Optionally enter a flow rate in GPM and a cost per gallon for fill-time and cost estimates.
- Read the volume in gallons, liters and cubic feet, plus fill time and chemical startup amounts.
| Result | What it means |
|---|---|
| Volume (gallons) | Total water the pool holds in US gallons. |
| Volume (liters) | The same volume converted to liters (1 gal = 3.78541 L). |
| Volume (cu ft) | Cubic feet of water space (1 cu ft = 7.48052 gal). |
| Fill time | Hours and minutes to fill at the flow rate you entered. |
| Chemical estimates | Typical startup amounts for chlorine shock, stabilizer and soda ash. |
| Water cost | Total fill cost based on the per-gallon rate you entered. |
What Is a Pool Volume Calculator?
A pool volume calculator uses the geometric formula for your pool shape to find how much water it holds. Knowing your pool volume is the starting point for every water-care decision: chemical dosing, pump sizing, heater selection and fill-time planning all depend on it.
The calculator supports the four most common residential pool shapes: rectangle, round, oval and freeform (kidney or irregular). It works in both feet and meters, and it always shows the result in US gallons, liters and cubic feet so you can use whichever unit your product labels require.
For other construction measurements, see the construction calculators hub.
How Does the Pool Volume Calculator Work?
The calculator finds the average depth, computes the water volume in cubic feet using the shape formula, then converts to gallons and liters.
Average depth = (shallow end + deep end) / 2Rectangle: volume = length x width x avg depth x 7.48052Round: volume = pi x (diameter / 2)^2 x avg depth x 7.48052Oval: volume = pi x (length / 2) x (width / 2) x avg depth x 7.48052Freeform: volume = length x width x avg depth x 7.48052 x 0.85The constant 7.48052 converts cubic feet to US gallons. The freeform shape factor of 0.85 accounts for the irregular outline of a kidney or free-form pool; it is an industry-standard approximation.
Unit Conversion
When you enter dimensions in meters the calculator converts them to feet internally (1 m = 3.28084 ft), runs the formulas, and shows the result in both gallons and liters.
Pool Volume Calculation Examples
Rectangle Pool
A 30 x 15 ft pool with a 4 ft shallow end and an 8 ft deep end.
Average depth = (4 + 8) / 2 = 6 ft.
Volume = 30 x 15 x 6 x 7.48052 = 20,197 gallons (76,455 liters).
At 8 GPM that takes about 20,197 / 8 = 2,525 minutes, or roughly 42 hours.
Round Pool
An 18 ft diameter pool at a 4 ft uniform depth.
Volume = pi x 9^2 x 4 x 7.48052 = 7,614 gallons.
Oval Pool
A 24 x 12 ft oval pool at 5 ft average depth.
Volume = pi x 12 x 6 x 5 x 7.48052 = 8,460 gallons.
Factors That Affect Pool Volume by Shape
Choosing the right shape formula is important for an accurate volume. Here is when to use each one.
| Shape | Use when | Accuracy |
|---|---|---|
| Rectangle | The pool has four straight sides and right-angle corners | Exact for the shape |
| Round | The pool is a circle (above-ground pools are often round) | Exact for the shape |
| Oval | The pool is elliptical with a longer and shorter axis | Exact for the shape |
| Freeform | Kidney, lagoon or any irregular outline | Approximate (0.85 shape factor) |
If your pool is L-shaped or has a connected spa, measure each section separately and add the volumes together.
Chemical Startup Estimates Explained
The calculator gives three common chemical startup guidelines. These are typical industry starting points, not exact prescriptions. Always test your water before adding chemicals.
Chlorine Shock
About 1 pound of calcium hypochlorite per 10,000 gallons to reach initial sanitation. Actual dosing depends on your starting chlorine level and the product concentration.
Stabilizer (Cyanuric Acid / CYA)
About 1 pound per 4,000 gallons to raise CYA by 10 ppm. A new pool usually targets 30 to 50 ppm, so you may need 3 to 5 times the single-dose amount.
PH Increaser (Soda Ash)
About 6 ounces per 10,000 gallons to raise pH by 0.2 units. Test the pH first and add soda ash only if the water is below the 7.2 to 7.6 target range.
The calculator labels these amounts as guidelines. Product labels and a water test kit give the precise dose for your water.
When to Use a Pool Volume Calculator
Dosing Pool Chemicals
Chlorine, shock, pH adjusters and stabilizer are dosed per 10,000 gallons. A wrong volume means every chemical dose is off by the same percentage.
Sizing a Pump and Filter
Pump turnover rate is volume divided by flow rate. The pool volume tells you the gallons-per-minute flow your pump must deliver for a target turnover time.
Planning the First Fill
Divide the gallons by your hose flow rate to estimate how long it takes to fill the pool, and check the water bill for the fill cost.
Budgeting for Water and Maintenance
Top-ups, backwashing and seasonal drains all depend on volume. Knowing the number up front helps you budget water and chemical costs for the season.
Fill Time and Water Cost Estimates
Fill time depends on your water source. A standard garden hose delivers roughly 5 to 10 gallons per minute (GPM). Fire hydrant fills and tanker deliveries are faster but need permits in most areas.
Estimating Fill Time
Fill time in minutes = pool volume in gallons divided by the flow rate in GPM. A 20,000-gallon pool at 8 GPM takes about 2,500 minutes, or roughly 42 hours.
Estimating Water Cost
Multiply the volume by your local cost per gallon. In the US, residential water typically costs $0.002 to $0.006 per gallon, so filling a 20,000-gallon pool might cost $40 to $120. Enter your rate for a site-specific estimate.
Common Mistakes When Calculating Pool Volume
1. Using Only One Depth
Most pools slope from shallow to deep. Using only the shallow end underestimates volume; using only the deep end overestimates it. Always average the two ends.
2. Confusing Diameter and Radius
The round-pool formula uses the diameter (full width), not the radius. Entering the radius doubles the error because the formula squares it.
3. Ignoring the Freeform Factor
A kidney or lagoon pool is not a full rectangle. Using the rectangle formula without the 0.85 factor overestimates the volume by about 15 percent.
4. Mixing Units
Entering some dimensions in feet and others in meters gives a meaningless result. Choose one system and stick with it.
5. Forgetting to Re-measure After Renovation
Resurfacing, adding a bench or changing the depth all change the volume. Recalculate after any structural change.
Accuracy and Limitations
The geometry formulas are exact for their ideal shapes. Real-world accuracy depends on how closely your pool matches the selected shape and how precisely you measure.
What it calculates accurately
- Volume for rectangle, round and oval pools from exact geometry
- Gallon-to-liter and gallon-to-cubic-foot conversions
- Fill time from a known flow rate
- Water cost from a known per-gallon rate
What it does not account for
- Irregular bottom contours, benches, steps or spa sections
- Plumbing volume in pipes and equipment
- Evaporation, splash-out or rain additions
- Product-specific chemical dosing (always read the label)
How We Calculate Your Pool Volume
Frequently Asked Questions About Pool Volume
How many gallons does my pool hold?
Multiply length by width by average depth by 7.48052 for a rectangular pool. A 30 x 15 ft pool with a 6 ft average depth holds about 20,197 gallons. Enter your dimensions above for the exact figure.
How do I calculate the volume of a round pool?
Use the formula pi times radius squared times depth times 7.48052. For an 18-foot-diameter pool at 4 feet deep that gives about 7,614 gallons.
What is the 7.48052 number?
It is the exact number of US gallons in one cubic foot. The calculator multiplies the cubic-foot volume by 7.48052 to convert to gallons.
How do I find the average depth of my pool?
Add the shallow-end depth and the deep-end depth, then divide by two. For a 4-foot shallow end and an 8-foot deep end, the average depth is 6 feet.
What is the 0.85 factor for freeform pools?
It reduces the bounding-rectangle volume by about 15 percent to account for the curved or irregular outline of a kidney or freeform pool. It is an industry approximation.
How long does it take to fill a pool with a garden hose?
A garden hose typically delivers 5 to 10 gallons per minute. Divide the pool volume by the flow rate. A 20,000-gallon pool at 8 GPM takes about 42 hours.
How much chlorine do I need for a new pool?
A common guideline is about 1 pound of calcium hypochlorite per 10,000 gallons for initial shock. Always test the water and follow the product label for your specific situation.
Can I use this calculator for an above-ground pool?
Yes. Select the round or oval shape and enter the diameter and water depth. The same volume formulas apply to above-ground pools.
How do I convert gallons to liters?
Multiply US gallons by 3.78541. The calculator does this automatically and shows both units.
Does this calculator account for steps or benches?
No. Steps, benches, sun shelves and spa sections reduce the actual water volume. Measure each section separately and subtract the solid portions, or use the result as an upper bound.
Sources
- Pool and Hot Tub Alliance (PHTA) volume guidelines (Formerly NSPF / APSP; industry-standard pool volume formulas and water-treatment references).
- US gallon to cubic foot conversion (NIST; 1 cu ft = 7.48052 US gal; authoritative unit definition).
- CDC Healthy Swimming - water chemistry (Centers for Disease Control and Prevention; pool water treatment and disinfection guidelines).
Related Calculators
Need more construction and home calculators?
Explore all construction calculatorsEducational estimate. Actual materials, quantities and requirements depend on local conditions, specific products and installation methods. Always verify measurements on-site before purchasing. Spotted an error? Let us know.
Author
Shakeel Muzaffar is the Founder and Editor-in-Chief of MultiCalculators.com, bringing over 15 years of experience in digital publishing, product strategy, and online tool development. He leads the platform's editorial vision, ensuring every calculator meets strict standards for accuracy, usability, and real-world value. Shakeel personally oversees content quality, formula verification workflows, and the platform's commitment to publishing tools that are genuinely useful for students, professionals, and everyday users worldwide.




