Used Mobile Home Value Calculator

Quick answer

To estimate a used mobile home value by year and size, enter width and length (16 x 80 is 1,280 sq ft), pick single or double wide, and the year built. The calculator starts from US Census Bureau average new-home prices, applies a depreciation rate you choose, and adjusts for condition. It is an estimate, not an appraisal.

Updated 2026-10-03Reviewed by Prof. Dr. Khalil Mudassar, PhD
Try
Manufactured Homes
Picks the matching Census price series: single-section or double-section new homes.
Listed width, such as 14, 16 or 28. Width x length gives the floor area.
Listed length, such as 56, 70 or 80.
If you know the measured or listed floor area, enter it here. It replaces width x length.
Size-based is usually best. The build-year option fills in the Census national average for your type and year (1980 to 2025); it is an average, not what your home cost.
$
Leave blank to use the Census 2025 average for your home type: about $79.78 single-section and $88.96 double-section. Use a local dealer price if you have one.
$
Used only when the starting value is set to original price.
From the data plate or HUD label. Age is counted from the current year.
Example value only. No official national rate exists; test 2 to 4 percent and compare with local sales.
Example value. Stops an old but usable home from falling to zero.
Your judgement, e.g. +10 excellent, 0 average, -10 fair, -25 poor.
Positive where similar homes sell above the estimate, negative where they sell below.
$
Permanent upgrades such as a new roof coating, HVAC or windows, at what a buyer would credit.
$
Estimated cost of needed repairs; subtracted from value.
$
Compares a listing or offer with the estimate in the verdict.

Estimated home value (no land)

--
Floor area used--
Starting value--
Age and share kept--
Range (rate +/- 1 point)--
Census avg new price: build year vs 2025--
Improvements minus repairs--
Asking price vs estimate--
Value per sq ft--

Calculations run in your browser. Inputs are not sent to our servers; anything you Save stays in this browser only.

Saved results (0)

How to Use the Used Mobile Home Value Calculator

  1. Choose single or double wide, then enter the width and length (for example 16 x 80). The tool multiplies them to get square feet. If you know the floor area, type it in the override box instead.
  2. Enter the year built from the data plate. Pick the starting value: size times a new-home price per square foot (blank uses the Census 2025 average), the Census average new price in your build year, or your original purchase price.
  3. Set your assumptions: yearly depreciation, the minimum share of value an old home keeps, a condition adjustment and a local market adjustment. The defaults are examples, not official figures.
  4. Add improvements a buyer would pay for and repairs a buyer would need. Optionally enter an asking or offer price to compare it with the estimate.

Here is what each result means:

ResultWhat it means
Estimated home value (no land)The home itself after depreciation and adjustments. Land or a lot lease is not included.
Floor area usedWidth x length, or the override you typed, in square feet.
Starting valueSize times price per square foot, the Census build-year average, or the original price.
Age and share keptYears since the build year and the percentage of the starting value that remains.
Range (rate +/- 1 point)The estimate again with depreciation one point higher and one point lower, to show how sensitive it is.
Census avg new price: build year vs 2025The official national average new price for your type in the year built and in 2025, and how many times higher the 2025 figure is. Shown for build years 1980 to 2025.
Improvements minus repairsThe net dollar adjustment you entered.
Asking price vs estimateHow far a listing or offer sits above or below the estimate.
Value per sq ftEstimate divided by floor area, for comparing listings of different sizes.

What Is a Used Mobile Home Value Estimate?

A used mobile home value estimate is a rough figure for what a pre-owned manufactured home might sell for, based on what a new one costs and how much value it has lost with age. It is a starting point for asking better questions, not a price anyone must accept.

Homes built to the federal standard are called manufactured homes. Federal rules at 24 CFR 3282.1 apply the HUD Code to homes that enter production on or after June 15, 1976. Older units are often called mobile homes, and the name is still used loosely for both. Single wide and double wide are the everyday names for the Census categories single-section and double-section.

The Census Bureau publishes prices for new homes only. Its glossary notes that prices of homes sold after placement are not collected, so no government table gives a used price by year, size or make. That is why this calculator shows its method openly and lets you set every assumption.

How Does the Used Mobile Home Value Calculator Work?

The calculator starts from a new-home value, keeps a share of it based on age, then applies your adjustments.

Formulas: Floor area = width x length | Starting value = floor area x new price per sq ft (or the Census build-year average, or the original price) | Share kept = max(minimum %, (1 - yearly rate)age) | Value = starting value x share kept x (1 + condition %) x (1 + market %) + improvements - repairs
  1. Starting value. The 2025 Census Manufactured Housing Survey reports an average new price of $85,600 for a single-section home of 1,073 square feet, about $79.78 per square foot, and $157,100 for a double-section home of 1,766 square feet, about $88.96. These prices include dealer set-up but exclude land. When you leave the price box blank, the tool uses these two per-square-foot figures.
  2. Year-built lookup. The same Census survey has average new prices back to 1980 for single and double homes. Choosing "Census average new price in the build year" starts from that figure for your type and year, with no size scaling, then depreciates it. It shows the price level of the year, not what your home cost.
  3. Depreciation. The tool uses declining balance: each year the home keeps (1 - rate) of the previous year's value. At 3 percent a year, a 21-year-old home keeps 0.9721 = 52.7 percent. The rate is your assumption, not an official schedule.
  4. Minimum value. A floor, such as 20 percent, stops the estimate reaching zero for a sound older home. At 3 percent, the floor takes over after about 53 years.
  5. Adjustments. Condition and market percentages scale the value; improvements add dollars and needed repairs subtract them.

Used Mobile Home Value Examples by Year and Size

All figures below were computed with the same formula the tool uses, valued in 2026, with a 3 percent yearly rate and a 20 percent floor. Those two numbers are examples, not official rates.

Example 1: 1998 Single Wide, 16 X 80

Floor area: 16 x 80 = 1,280 sq ft. Starting value: 1,280 x $79.78 (Census 2025 single-section average) = $102,114. Age: 28 years, so the share kept is 0.9728 = 42.62 percent.

Estimate: $43,520. At 4 percent the figure is $32,560 and at 2 percent it is $57,998. That spread shows why your depreciation assumption matters more than any other input.

Example 2: 2005 Double Wide, 28 X 70

Floor area: 28 x 70 = 1,960 sq ft, which is twice the 980 sq ft of a 14 x 70. Starting value: 1,960 x $88.96 = $174,358. Age: 21 years, share kept 52.75 percent. Estimate: $91,970.

Example 3: 1996 Double Wide from the Build-year Average

The Census average new double-section price in 1996 was $46,200, against $157,100 in 2025, so the 2025 figure is 3.4 times higher. Age is 30 years and the share kept is 40.10 percent, giving $18,527. Starting from 1996 prices gives a much lower number than starting from today's price per square foot (for an 1,800 sq ft home that route gives $64,211), because it ignores 30 years of price rises. Use it when you have only the year and type, and treat it as the low side.

Census Average New Mobile Home Price by Year, 1980 to 2025

These are the official national averages the year-built lookup uses, in dollars of the year shown (not adjusted for inflation). They are prices of new homes, not used values.

YearSingle wideDouble wideAll homesCensus series
2025$85,600$157,100$127,200Sold or intended for sale
2024$85,200$152,000$123,300Sold or intended for sale
2023$84,800$154,100$124,300Sold or intended for sale
2022$86,400$158,600$127,300Sold or intended for sale
2021$72,600$132,000$108,100Sold or intended for sale
2020$57,300$108,500$87,000Sold or intended for sale
2019$53,200$104,000$81,900Sold or intended for sale
2018$52,400$99,500$78,500Sold or intended for sale
2017$48,300$92,800$71,900Sold or intended for sale
2016$46,700$89,500$70,600Sold or intended for sale
2015$45,600$86,700$68,000Sold or intended for sale
2014$45,000$82,000$65,300Sold or intended for sale
2013$42,200$78,600$64,000Placed
2012$41,100$75,700$62,200Placed
2011$40,600$73,900$60,500Placed
2010$39,500$74,500$62,800Placed
2009$39,600$74,500$63,100Placed
2008$38,000$75,800$64,700Placed
2007$37,300$74,200$65,400Placed
2006$36,100$71,300$64,300Placed
2005$34,100$68,700$62,600Placed
2004$32,900$63,400$58,200Placed
2003$31,900$59,700$54,900Placed
2002$30,900$56,100$51,300Placed
2001$30,400$55,200$48,900Placed
2000$30,200$53,600$46,400Placed
1999$29,300$51,100$43,300Placed
1998$28,800$49,800$41,600Placed
1997$27,900$48,100$39,800Placed
1996$27,000$46,200$37,200Placed
1995$25,800$44,600$35,300Placed
1994$23,500$42,000$32,800Placed
1993$21,900$39,600$30,500Placed
1992$20,600$37,200$28,400Placed
1991$19,900$36,900$27,700Placed
1990$19,800$36,600$27,800Placed
1989$19,600$35,700$27,200Placed
1988$18,600$33,600$25,100Placed
1987$18,400$32,400$23,700Placed
1986$17,800$30,800$22,400Placed
1985$17,800$30,100$21,800Placed
1984$17,700$30,400$21,500Placed
1983$17,600$30,500$21,000Placed
1982$17,200$28,400$19,700Placed
1981$16,700$29,200$19,900Placed
1980$16,000$28,500$19,800Placed

Two series are joined here. Years 1980 to 2013 come from the Census old-series table of new homes placed. Years 2014 to 2025 come from the annual table of new homes sold or intended for sale. The definitions differ slightly, so compare across 2013 and 2014 with care. Dealers are told to include set-up costs, and some extra site costs may not be included.

Square feet are published only from 2014. In 2025 the Census average floor area was 1,073 sq ft for single-section and 1,766 sq ft for double-section homes.

Mobile Home Size Chart: Width X Length in Square Feet

Floor area is width times length. The table is plain arithmetic for example sizes, and the Census figures above give the averages for comparison.

Width x length (ft)Area
12 x 60720 sq ft
14 x 56784 sq ft
14 x 66924 sq ft
14 x 70980 sq ft
14 x 801,120 sq ft
16 x 661,056 sq ft
16 x 761,216 sq ft
16 x 801,280 sq ft
18 x 761,368 sq ft
18 x 801,440 sq ft
24 x 40960 sq ft
28 x 561,568 sq ft
28 x 661,848 sq ft
28 x 701,960 sq ft
28 x 762,128 sq ft
32 x 802,560 sq ft

To go the other way, divide: width = square feet / length. A 1,344 sq ft home that is 56 ft long is 1,344 / 56 = 24 ft wide. Listed sizes can be rounded or measured differently, so type the measured floor area in the override box when you have it. Larger sizes cost more in total but not always more per square foot, so compare per square foot, as in the Census figures.

Factors That Change a Used Mobile Home Value

Local sales decide the real price, but these factors explain most of the difference between two homes of the same age.

Land or Lot Lease

A home on owned land is often sold as real estate with the land. A home in a land-lease community is usually sold as personal property, and the lot rent affects what buyers will pay. This tool values the home only, so add land value separately.

Age and HUD Code Status

Every dwelling unit of a HUD Code home carries a data plate under 24 CFR 3280.5. Homes built before June 15, 1976 were not built to the federal standard, which can limit buyers and financing.

Size and Sections

Double-section homes cost more per square foot new, according to the Census figures, so pick the type that matches your home.

Make and Model

The make and model are printed on the data plate, but no free official dataset prices them, so this tool has no make setting. Compare similar homes of the same make in your area instead.

Condition and Systems

Roof, floors, plumbing, heating and skirting condition change what a buyer offers. A realistic repair figure is often more useful than a vague condition label.

Moving Costs

When the buyer must move the home, transport and set-up come out of what they will pay. Enter these as repairs to see the effect.

Estimate Methods Compared: Calculator, Valuation Guide, Appraisal

Several ways exist to put a number on a used manufactured home. They differ in cost, data and who accepts them.

MethodWhat it usesBest for
This calculatorCensus new-home prices plus your depreciation, condition and market assumptionsA quick, transparent first estimate
Commercial valuation guideProprietary data by make, model and year; this page uses none of itDealers and lenders that use one
Comparable local salesRecent sale prices of similar homes nearbySetting or checking an asking price
Licensed appraisalAn inspection plus market data by a licensed professionalLoans, estates, divorce and legal matters
Tax assessmentYour local assessor's own methodProperty tax only; may differ from market value

For the financial side, the home affordability calculator checks whether a purchase fits your income, the closing costs calculator estimates fees on a real estate sale, and the rent vs buy calculator compares owning with renting.

When to Use This Estimate

Before Listing a Home for Sale

Get a first figure, then compare it with local listings and sold prices before setting an asking price.

Before Making an Offer

Enter the asking price. The verdict shows how far it sits from your estimate, which is a prompt to ask for comparable sales and inspection results.

Planning Improvements

See how a repair changes the estimate. A buyer rarely credits the full cost of an upgrade, so enter a conservative figure.

Tracking Value Over Time

Depreciation is a form of wear-down in value. The accumulated depreciation calculator shows the same idea for other assets.

Common Mistakes

1. Treating the Estimate as an Appraisal

It is a model built from your assumptions. Lenders and courts need a licensed appraisal or their own guide.

2. Mixing Up the Home and the Land

Census prices and this estimate exclude land. A home sold with its own lot needs a land value added from local data.

3. Using an Old Purchase Price Without Thinking

A price paid decades ago ignores the large rise in new-home prices; the Census series shows the 2025 single-section average is 3.0 times the 1998 average. The size-based starting value is usually more realistic.

4. Choosing Extreme Depreciation

A rate that is too high sends value toward the floor within a few years. Test several rates and see which matches local sales.

5. Ignoring the Data Plate

The data plate lists the manufacturing plant, serial number, model and date of manufacture. Missing labels can complicate a sale.

6. Expecting a Serial Number to Give a Price

A serial number identifies the home but is not a price lookup. Use it to confirm the year and model, then compare local sales.

Accuracy and Limitations

The maths is exact and transparent, but the estimate is only as good as the assumptions and local knowledge you add.

What it calculates accurately

  • Floor area from width x length
  • Starting value from size and a stated price per square foot, or the Census build-year average
  • Declining-balance depreciation with a minimum floor
  • Condition, market and dollar adjustments exactly as entered
  • The gap between an asking price and the estimate

What it does not account for

  • Actual recent sales near you
  • Land value, lot rent or park rules
  • Make, model or manufacturer
  • Regional price differences (the Census averages are national)
  • Title, lien or permit problems
  • Moving, set-up or financing limits

How We Calculate Used Mobile Home Value

Method
Starting value x max(floor, (1 - rate)age) x (1 + condition) x (1 + market) + improvements - repairs, never below zero.
Inputs used
Home type, width, length or floor area, starting-value basis, price per square foot or original price, year built, yearly rate, floor, condition, market, improvements, repairs and an optional asking price.
Price data
US Census Bureau Manufactured Housing Survey, United States averages, read 2026-10-03: annual tables 2014 to 2025 (page revised June 12, 2026) and the old-series table 1980 to 2013. 2025: $85,600 single (1,073 sq ft), $157,100 double (1,766 sq ft), $127,200 all. Dealer set-up included; land excluded.
Assumptions
Depreciation rate, floor, condition and market figures are user assumptions with example defaults. No official national depreciation schedule is used or implied.
Age
Current calendar year minus build year. A build year before 1976 triggers a warning; 1976 prompts a label check.
Rounding
Money to cents; percentages to one decimal. Full precision is kept until display.
Sources
US Census Bureau and the Electronic Code of Federal Regulations (listed under Sources below).
Last reviewed
2026-10-03.

Frequently Asked Questions About Used Mobile Home Value

Is there a mobile home blue book I can use for free?

Not an official one. Recognised valuation guides are commercial products with their own data, and this page does not use or copy them. It gives a transparent estimate from Census new-home prices and assumptions you choose.

How do I find the value of a mobile home by year?

Enter the year built and pick single or double wide. The tool shows the Census average new price for that year (1980 to 2025), then depreciates a starting value you choose. Compare the result with recent local sales.

How many square feet is a 14x70, 16x80 or 28x70 mobile home?

Multiply width by length: 14 x 70 is 980 sq ft, 16 x 80 is 1,280 sq ft and 28 x 70 is 1,960 sq ft. Listed sizes can be rounded, so use the measured floor area when you know it.

Is a double wide worth more than a single wide?

New double-section homes cost more in total and per square foot. The 2025 Census averages are $157,100 against $85,600. Used values still depend on condition, land and local sales.

Does the make or manufacturer change the value?

It can, but no free official data prices homes by make, so this tool has no make setting. The data plate lists the manufacturer; compare local sales of the same make.

How fast do mobile homes depreciate?

No official national rate exists. The tool lets you test rates, and its 3 percent default is only an example. Compare the results with recent local sales to see which rate fits your area.

Can I look up a mobile home value by serial number?

No. The serial number and date of manufacture on the data plate identify the home, but they do not give a price. Use them to confirm year and model.

Does the estimate include the land?

No. It values the home only. Add a land value from local sales when the home is sold with its own lot.

Why does the build year 1976 matter?

Federal rules apply the HUD Code to homes that entered production on or after June 15, 1976. Homes built earlier were not built to that standard.

Can I use the original purchase price instead?

Yes. Switch the starting value to original price. It ignores changes in new-home prices since the purchase, so it often understates value.

Sources

Related Calculators

Working out other costs of owning a home?

Explore all home cost calculators

This calculator gives an educational estimate only. It is not an appraisal, a valuation guide figure, a loan value or financial advice. Every depreciation and condition figure is an assumption you control. For a sale, loan, tax appeal, insurance claim or legal matter, use a licensed appraiser, your lender or your local tax assessor. Not affiliated with the US Census Bureau or any manufacturer or valuation guide. Spotted an error? Let us know.

Author

shakeel-Muzaffar
Founder & Editor-in-Chief at  ~ Web ~ More Posts

Shakeel Muzaffar is the Founder and Editor-in-Chief of MultiCalculators.com, bringing over 15 years of experience in digital publishing, product strategy, and online tool development. He leads the platform's editorial vision, ensuring every calculator meets strict standards for accuracy, usability, and real-world value. Shakeel personally oversees content quality, formula verification workflows, and the platform's commitment to publishing tools that are genuinely useful for students, professionals, and everyday users worldwide.